My Report (&Account)

Manufacturing Processes Online Test


Correct Answer: 2 points | Wrong: -1 point
Grades: A* (100% score) | A (80%-99%) | B (60%-80%) | C (40%-60%) | D (0%-40%)

Here is the complete list of test quizzes on Manufacturing Processes.

1. Circumference of a work piece is to be divided into 60 equal divisions using simple indexing method having 40 worm wheel teeth. Indexing movement will be

Question 1 of 50

2. What is the coordination number of a simple cubic (SC) unit cell?

Question 2 of 50

3. In machining metals, chips break due to _____________ of work material.

Question 3 of 50

4. According to ASTM standard, which of the following relation is correct about gauge length of cross section area ‘A’?

Question 4 of 50

5. Which of the following material can be used for coating on tools?

Question 5 of 50

6. Which of the following part of milling machine can be used for reservoir for coolant?

Question 6 of 50

7. Silicon oil applied between two contact surfaces will?

Question 7 of 50

8. Which of the following tool will give the best result for machining of brass?

Question 8 of 50

9. Which of the following material cannot be machined using electro chemical machining?

Question 9 of 50

10. With an increase in the thickness of insulation around a circular pipe, heat loss to surrounding due to ____________

Question 10 of 50

11. Flank wear occurs at

Question 11 of 50

12. Which of the following part of slotting machine carries table elevating mechanism?

Question 12 of 50

13. In the gate area for non-pressurized casting gating ratio a:b:c? (gating ratio = a: b: c where, a = cross-sectional area of sprue, b: cross-sectional area of runner, c = total cross-sectional area of ingates).

Question 13 of 50

14. The word ceramic stands for which of the following meaning?

Question 14 of 50

15. Grinding wheel is specified as "A 600 K 5 B 17". Grain size of a wheel will be

Question 15 of 50

16. Which casting is used to make hollow casting with thin walls?

Question 16 of 50

17. Total load is distributed over all teeth when thread cutting is done using thread chaser.

Question 17 of 50

18. What is the function of a torch?

Question 18 of 50

19. In which of the following forging operation no special die is used?

Question 19 of 50

20. Which of the following parameter is used to assess the magnetic ability of a material?

Question 20 of 50

21. Which of the following material can be machined using electro chemical machining?

Question 21 of 50

22. Slotted link of crank and slotted lever mechanism is also known as

Question 22 of 50

23. Top surface of tooth is known as

Question 23 of 50

24. During taper turning operation 100mm of smaller side diameter and 800mm of bigger side diameter was required. What will be the value of taper gradient for a job of 1m in length?

Question 24 of 50

25. Which of the following furnaces are heated with various fuels, such as commercial gases, fuel oil, and fossil fuel, as well as electricity?

Question 25 of 50

26. Resistance developed by surface of any material is known as ____________

Question 26 of 50

27. Contact ratio is given by

Question 27 of 50

28. Moving a small straight punch up and down rapidly into a die is done by a process known as?

Question 28 of 50

29. The basic difference between MRP and MRP-II is:

Question 29 of 50

30. Which of the following grinding wheel would be more economical for grinding of soft work piece?

Question 30 of 50

31. Which of the following position of tumbler gear lever set will move carriage towards headstock of the lathe?

Question 31 of 50

32. Which of the following code is used to select y-z plane in milling?

Question 32 of 50

33. The junction between weld face and base metal is known as?

Question 33 of 50

34. Major constituent of the gun metal is ____________

Question 34 of 50

35. Which of the following is a standard pressure angle in degree?

Question 35 of 50

36. In which of the following process plastic deformation takes place?

Question 36 of 50

37. Grinding ratio generally lies between

Question 37 of 50

38. Which of the following is used to give power feed during cutting of threads?

Question 38 of 50

39. For grey cast iron, which of the following welding methods is preferable?

Question 39 of 50

40. Ratio of circumference of pitch circle to number of teeth is known as

Question 40 of 50

41. Which of the following defects occur due to flux employed and electrode coating?

Question 41 of 50

42. A small funnel shaped cavity at the top of the mould into which the metal is poured is known as?

Question 42 of 50

43. Which of the following is characteristic of non-crystalline structures?

Question 43 of 50

44. If there are 930 grains per mm2 on a photomicrograph of a metal at 2X, what is the ASTM grain size number of the metal?

Question 44 of 50

45. Cutting of material during slotting operation takes place in

Question 45 of 50

46. When the value of helix angle increases in drills, the value of required torque for rotation of drill will

Question 46 of 50

47. With time, grinding wheel starts rubbing work piece instead of cutting, due to a decrease in sharpness. This phenomenon is known as

Question 47 of 50

48. Which of the following is not true about fusion welding?

Question 48 of 50

49. Which of the following statements about “projection welding” is correct?

Question 49 of 50

50. Which of the following sand is black in color?

Question 50 of 50


 

Topic wise Test Quizzes on Manufacturing Processes

Manufacturing Processes tests, quizzes, and exams are great ways to learn and test your Manufacturing Processes skills. Whether you’re a beginner or experienced, challenge and boost your confidence with our engaging online quizzes on Manufacturing Processes Basics, Mechanical Properties, Phase Diagram, Ferrous and Non-Ferrous Metal, Plastics, Ceramics and Composite, Metal Cutting, Cutting Mechanics, Lathe Machine, Milling Operation, Grinding, Machining Processes, Fusion Welding Processes, NC Part Programming, Casting, Forging Operation, Gear Terminology, Manufacturing and Automation. Start the Manufacturing Processes online test now!

Manufacturing Processes Basic Quiz

Mechanical Properties and Testing Quiz

Phase Diagram Quiz

Ferrous and Non-Ferrous Metal Quiz

Material Properties Quiz

Plastics, Ceramics and Composite Quiz

Tool Geometery and Nomenclature Quiz

Metal Cutting Quiz

Cutting Mechanics Quiz

Lathe Machine Quiz

Shaping and Slotting Quiz

Milling Operation Quiz

Twist Drill Geometry Quiz

Grinding Quiz

Surface Finishing Operation Quiz

Machining Processes Quiz

Welding Basic Quiz

Resistance Welding Quiz

Fusion Welding Processes Quiz

Powder Metallurgy Operation Quiz

NC Part Programming Quiz

Casting Basic Quiz

Casting Defects Quiz

Expendable Mold Casting Quiz

Forging Operation Quiz

Metal Forming Processes Quiz

Jigs and Fixture Quiz

Manufacturing and Automation Quiz

Gear Terminology Quiz


Manufacturing Processes I Certification Test

Manufacturing Processes I Certification Test is a free certification exam. However, you need to score an A grade in each of the "Certification Level Tests 1 to 10" to be eligible to take part in this certification test. So, take all the "10 Tests" starting from Certification Level 1 upto Level 10, before taking the final Certification test.

Level 1 Test Certification Test

Level 1 to 10 Tests:
Total Questions: 25, Total Time: 30 min, Correct Answer: 2 points, Wrong Answer: -1 point

Certification Test:
Total Questions: 50, Total Time: 1 hour, Correct Answer: 2 points, Wrong Answer: -1 point

Manufacturing Processes I Internship Test

If you scored either Grade A* or Grade A in our Manufacturing Processes I Internship Test, then you can apply for Internship at Sanfoundry in Manufacturing Processes I.

Manufacturing Processes I Internship Test

Total Questions: 50, Total Time: 1 hour, Correct Answer: 2 points, Wrong Answer: -1 point

Manufacturing Processes I Job Test

It is designed to test and improve your skills for a successful career, as well as to apply for jobs.

Manufacturing Processes I Job Test

Total Questions: 50, Total Time: 1 hour, Correct Answer: 2 points, Wrong Answer: -1 point

Note: Before you get started on these series of online tests, you should practice our collection of 1000 MCQs on Manufacturing Processes I .

Sanfoundry Scoring & Grading System

Sanfoundry tests and quizzes are designed to provide a real-time online exam experience. Here is what you need to know about them.

  • Scoring System: You get 2 points for each correct answer but lose 1 point for every wrong answer.
  • Grading System: Your grade depends on your final score and can be one of the following:

    • Grade A* - Genius (100%)
    • Grade A - Excellent (80% to 99%)
    • Grade B - Good (60% to 80%)
    • Grade C - Average (40% to 60%)
    • Grade D - Poor (0% to 40%)
advertisement
advertisement
Manish Bhojasia - Founder & CTO at Sanfoundry
Manish Bhojasia, a technology veteran with 20+ years @ Cisco & Wipro, is Founder and CTO at Sanfoundry. He lives in Bangalore, and focuses on development of Linux Kernel, SAN Technologies, Advanced C, Data Structures & Alogrithms. Stay connected with him at LinkedIn.

Subscribe to his free Masterclasses at Youtube & discussions at Telegram SanfoundryClasses.